Understand the Nitrogen Cycle
Understand the Nitrogen Cycle
The aquarium nitrogen cycle information presented below may be rather boring to most people, but it is absolutely essential to understand this process if you want to be successful at keeping fish!
Some call it the biological cycle, the nitrification process, new tank syndrome or even the start-up cycle. They all are referring to the same cycle – The Nitrogen Cycle. The aquarium nitrogen cycle is a very important process for the establishment of beneficial bacteria in the aquarium and in the filter media that will help in the conversion of ammonia to nitrite and then the conversion of nitrite to nitrates. Check out the aquarium water chemistry page (on the left) for more information on these terms.
This process can take from 2 weeks to 2 months or longer to complete. It is vital for anyone planning on keeping aquarium fish to understand this process. Learning about this process will help you to be successful in keeping fish and it should definitely improve your chances when keeping tropical fish. The best way to monitor the nitrogen cycle is to purchase an aquarium test kit that will test for ammonia, nitrites, nitrates and ph.
Test your aquarium water every other day and write down your readings. You will first see ammonia levels rising. A few weeks or so later you should see the nitrite levels rising and the ammonia levels dropping. Finally, after a few more weeks you should see the nitrate levels rising and the nitrite levels dropping. When you no longer detect ammonia or nitrites but you can detect nitrates you can assume that it is safe to add your tropical fish.
Nitrogen Cycle Stages
Ammonia is introduced into the aquarium via tropical fish waste and uneaten food. The tropical fish waste and excess food will break down into either ionized ammonium (NH4) or un-ionized ammonia (NH3). Ammonium is not harmful to tropical fish but ammonia is. Whether the material turns into ammonium or ammonia depends on the ph level of the water. If the ph is under 7, you will have ammonium. If the ph is 7 or higher you will have ammonia.
Soon, bacteria called nitrosomonas will develop and they will oxidize the ammonia in the tank, essentially eliminating it. The byproduct of ammonia oxidation is Nitrites. So we no longer have ammonia in the tank, but we now have another toxin to deal with – Nitrites. Nitrites are just as toxic to tropical fish as ammonia. If you have a test kit, you should be able to see the nitrite levels rise around the end of the first or second week.
Bacteria called nitrobacter will develop and they will convert the nitrites into nitrates. Nitrates are not as harmful to tropical fish as ammonia or nitrites, but nitrate is still harmful in large amounts. The quickest way to rid your aquarium of nitrates is to perform partial water changes. Once your tank is established you will need to monitor your tank water for high nitrate levels and perform partial water changes as necessary.
There are other methods to control nitrates in aquariums besides water changes. For freshwater fish tanks, live aquarium plants will use up some of the nitrates. In saltwater fish tanks, live rock and deep sand beds can have anaerobic areas where denitrifying bacteria can breakdown nitrates into harmless nitrogen gas that escapes through the water surface of the aquarium.
Getting The Nitrogen Cycle Started
There are two ways to get the aquarium cycle started, either with fish or without fish.
Starting The Nitrogen Cycle With Fish
This is not the preferred way to get the nitrogen cycle started because the fish are being exposed to ammonia and nitrites during this process. Many fish can not and will not make it through the cycling process. Often times the fish become stressed and fish disease starts to break out. I wonder what percentage of disease is caused by the cycling of new aquariums?
Certain species are hardier than others and seem to tolerate the start-up cycle better than others. For freshwater tanks, the zebra danio is a very hardy fish that many use to get the nitrogen cycle started. For saltwater tanks, some have reported success using damselfish to get the process started. Again, using fish to cycle is not a good idea and you may be throwing your money (on dead fish) out the window. There is a better way. Read on, young grasshopper.
Starting The Nitrogen Cycle Fishless
There are a few different ways to get this process started. To easily get an ammonia reading from your tank water try the Seachem Ammonia Alert. It sticks inside the tank and has a circle that changes color depending on the ammonia levels in the tank.
Using Fish Food
Drop in a few flakes every 12 hours. As the food decomposes it will release ammonia. You will have to continue to “feed” the tank throughout the process to keep it going.
Use a small piece of raw fish or a raw shrimp
Drop a 2 inch by 1 inch chunk of raw fish or a raw shrimp into the tank. As it decomposes it will release ammonia into the tank.
Use 100% pure ammonia.
Using a dropper, add 5 drops of ammonia per 10 gallons of aquarium water. If you don’t get an ammonia reading with your test kit, add some more drops until you start to see an ammonia reading. Keep track of how many drops you’ve used so you can repeat this process daily. Continue to dose the tank with ammonia until you start to get nitrite readings with your test kit. Once you can detect nitrites you should only add 3 drops of ammonia per 10 gallons of aquarium water, or if you added more drops originally to get an ammonia reading cut the amount of drops used in half. Continue this process daily until you get nitrate readings with your test kit. Do a 30% water change and your tank is ready.
Use gravel and/or filter media from an established and cycled tank
This is the best and fastest way to go. This will seed the tank with all of the necessary bacteria for the nitrogen cycle. “Feed” the tank daily with flake food until you are getting nitrate readings. Depending on how fast you were able to get the gravel and filter media into your tank, you may be getting nitrate readings in only a day or two. There are some drawbacks to this method. Ask your source if they have recently used any copper medications in the tank. If they have and you are planning to have invertebrates in the tank you should probably not use this method. Invertebrates will not tolerate copper. Get a copper test kit to determine if it’s safe to use.
Using live rock in Saltwater Tanks
The use of live rock in saltwater tanks has really taken off over the past few years. The reason for this is because it is one of the best forms of biological filtration available for saltwater tanks. The shape the rock is in when you get it will determine how long the nitrogen cycle will take. See step 7 on the saltwater setup page for more information on live rock.
Use Colonize by Dr. Foster and Smith – claims to colonize your water with the necessary bacteria needed to get the cycle going along with detoxifying ammonia so it doesn’t harm the fish. To be used at the start of the tank setup and whenever you add new fish to your tank.
Another bacteria culture product is Tetra SafeStart. People have reported success on the forum with using Tetra SafeStart. Do a quick search on the forum for other members’ input.
Use Instant Ocean BIO-Spira for Saltwater Tanks made by Marineland (the freshwater version may have been discontinued). This product claims to contain some patent pending species of nitrifying bacteria that will cycle your tank in 24 hours. Some of the FishLore forum members have tried it and it sounds like it is legitimate. It is kind of expensive, but if you already have fish in your tank and they are suffering through the cycle, you may want to check this stuff out. 1 ounce of this product is supposed to treat a 30 gallon freshwater tank. There are both freshwater and saltwater versions of Bio-spira. Please let us know if you use this and if it works for you by submitting comments below.
Once the cycle has started only add one or two fish at a time. Wait a couple of weeks before adding more fish. This will give your tank the time it needs to catch up with the increased bio-load.
Speeding Up the Cycling Process
There are things you can do to speed along the process of cycling your aquarium.
Increase the temperature of your aquarium water to 80°F-82°F (27°C-28°C)
Get some beneficial bacteria colonies. Borrow some gravel from an established and cycled aquarium. If you have another tank with an extra filter you can use it. If you have a really nice friend with an established and cycled aquarium, ask if you can have one of their used filter media. It will be loaded with the good bacteria that we are looking for.
There are products on the market that claim to introduce the beneficial bacteria. For more information, check out products like Bio-spira and Tetra SafeStart in option 6 above. There are many more products entering the market that contain the beneficial bacteria necessary to seed your tank. Between live rock (for saltwater aquariums) and the bottled bacteria being readily available, there really is no excuse to make fish suffer through a cycle.